• <dd id="r5cve"><optgroup id="r5cve"></optgroup></dd>

        Mr. KE:153 9520 9958
        Mr. QI:133 3552 4412
        Mr. DING:180 5523 2533
        Megan:188 9563 9870

        Bengbu Jixin Communication Machinery Co., Ltd.
        • 1
        • 2
        • 3
        • 4
        JX-280
        • clicks:2196
        • Product Category: Products Fiber thermal stripping pliers
        • product description:
        • JX-280 Manual Fiber Stripper Manual


          ADDRESS:Bengbu, Anhui Province Huangshan Road, Building 8, No. 8318

          TEL:0552-4080043

          FAX:0552-4125325

          Product name :(Auto fiber Stripper)(for example Figure 1)


          model: JX-280

          Important safety precautions

          This product has been designed and manufactured to assure personal safety.Improper use can result in bodily injury and serious damage to the jacket remover,please read and observe all warnings instructions given in this operation manual.

          The meaning of warning signs,this product has the following signs,please carefully read and understand the contents

          Logo graphic mean.

          Note that the natation cantains darger ,warning means.the instructions on the product and the graphical representation of the general’s attention,danger,warning means.

          *please read carefully befor use warnings and precautions

          1、forword

          Thank you very much for purchasing the forst use of the campany JX-280 auto fiber stripper. This product has the advantages of convenient use, automatic vertical stripping, high quality, high performance and high efficiency. The blade is durable and easy to change. The machine adopts high precision linear guide and electric motor directly driven by the hot strip method, which ensures no damage to the fiber..Before using the product,read this manual carefully in its entirety to fully understand product capabilities.Save this manual in a location in which you can easily get to see

          2、Basic introduction to the product

          ◆Product specifications and main technical parameters

          ◆Fiber choice


          ◆standard


          3、Structure

          ◆Figure 1 shows Machine basic structure

          ◆Function Keys: Function keys shown in Figure 2

          1、Power button For the product power on and off, that power: Press the "Power" button for 1 second or so to see the power indicator light on the release line; off: Press and hold "Power" button 4-5 seconds after the release, see the power light off on the line. It is worth noting that, only when the motor is in the reset state (that is, the optical fiber is fixed on the right side of the seat), the function is effective.

          2、Temperature key Temperature control for heating, the product control panel on the "temperature" button corresponding to the four panes from the bottom up followed by 90 ℃, 100 ℃, 110℃ and 120 ℃ were fourth gear temperature, red light represents the file successfully set temperature , power-on default temperature is 100 ℃, the control panel click on the "temperature" key in ascending order of temperature 10 ℃, when the temperature reaches 120 ℃, the click "temperature" button, the temperature has become 90 ℃, followed by cycles can be adjusted . Users can choose according to actual needs, It is worth noting that, only when the motor is in a reset state (that is, the fiber optic fixed seat at the right side), the temperature adjustment function is effective.

          3、Heating time adjustment key(TIME) For heating time adjustment, the product operation panel on the "TIME" button corresponding to the four 8S, 4S, 6S and 2S four files, red light on behalf of the file is set up successfully, the default temperature is 2S, press the "TIME" button on the operating panel to heat up the 2S, then press the "TIME" button, the heating time is 2S, can be adjusted in turn.

          4、Preparing the power supply

          Using the power adapter into power DC12V

          5、Methods of operation

          1、Connect the power adapter to both ends of the AC220V power and thermal stripping Power Interface; 2、Press the power button to start the motor automatically reset, the indicator light shows normal.

          3.The left cover plate and the press cover are opened, and the fixture with good optical fiber is arranged in the middle groove of the optical fiber;

          4.Cover the upper left cover plate (gently press the clip, make the fiber optic press firmly) and the pressure and the cover;

          5.Pressure fiber cover, wait about 3 seconds to start the automatic fiber stripping machine;

          6.And so on the motor automatically stops, the end of the fiber;

          7.Open the left cover plate and press the fiber cover, remove the good fiber, about 3 seconds, the motor automatically return to the initial position;

          8,left cover, followed by pressure-fiber cover open, remove the fixture and with the fiber, please do not forget to note that after stripping out each strip of the coating layer;

          9、Use a purity of more than 99% alcohol soaked gauze clean fiber direction of the arrow (Figure 6);

          10、Fiber top flick with your fingers, so that fiber does not overlap neatly arranged (Figure 7);

          11、Press "Power" button 1 seconds after the release, the power light is off, turn off and unplug the power adapter.

          ★Please do not re-used with gauze; Please be careful not to hurt your fingers fiber top.

          *Note: do not use the machine should be shut down more than 5 minutes over hot stripping pliers, and unplug the power plug, to avoid prolonged heating in air machine state, the shortening of the life of hot-stripping pliers.

          6、Maintain

          ◆Daily cleaning To enable the normal functioning of this product, must be cleaned before and after maintenance, please use the 99% ethanol alcohol-soaked cotton swab cleaning blade, heating plate and rubber parts. Fixture and the host of the tank is cleaned the same way.


          ◆Blade replacement Blade is very sharp, the operation required more attention. Exchange to ensure safety, make sure that the host must be in the following states: 1、Power off; 2、Heating film is cooled state (after power is turned off, please wait 3 minutes or more)

          *Note: Please also replace the blade up and down, up and down the blade is no different

          ◆ATC procedures:

          1. Fixed blade with a hex wrench to loosen the screws, remove the blade up and down;

          2. Install the new blade on the lower part, the use of screws, and is not completely fixed state (Figure 8); 3. Install the new blade on the upper part, the use of screws, and is not completely fixed state (Figure 8)

          4. Slightly up and down the blade of the screw will tighten, keeping the blade can be moved around a very small margin; Please confirm whether the blade moves up and down the room

          5、Adjust the upper blade Closing pressure-fiber cover, and compaction pressure fiber cover and holder, with a hex wrench pressure above the top of the silk fiber cover (Figure 9) onto the blade up and down in place so that there is no gap (except knife) and tighten around the lower part of the fixed blade Tighten the screws, note the power evenly, the seamless alignment. Then tighten the screws around the upper part of the blade;


          6、By test-cutting steps, and then observe the effect of fiber stripping, to test whether adjusting the blade 7、Frequently Asked Questions


          Fiber coating stripping bad, mainly for the following reasons:

          (A) Cleaning is not complete Blade, heating plate and the rubber part on the residual slag coating, strip coating will lead to poor. Follow the [daily cleaning] the project again clean.

          (B) Blade does not cut into the coating

          1、As the blade properly adjusted can cause this situation. Please refer to [blade replacement] of the project, verify the correct installation of the blade, the blade whether there is loosening screws.

          2. Blade wear Even the location of the blade has been adjusted to the appropriate location, or place the issue of poor strip, it may be because the blades wear, please contact our service center. See back cover telephone service center page.

          3. Heating temperature did not reach the predetermined temperature may also happen. In the strip coating, please observe the state of the heating lamp. Coating layer is difficult to strip, strip the coating easily broken.

          1、 the coating material, ambient temperature and other factors, you can use the machine key to set the temperature of the heating temperature is more appropriate. Ambient temperature is generally low, raising the temperature of the heating film, can be more easily stripped;

          2, and the quality of the ribbon fiber itself, the poor quality of the optical fiber may also lead to peeling of the coating layer break.

          Thank you carefully read the complete instructions! Zhu Guigong Division flourishing!

          Product Category 


        Add.:No.8318, Huangshan Avenue, Bengbu City, Anhui Province, China233010

        Foreign Trade Dep.: [email protected],E-mail:[email protected] 

           Website:www.wgfcy.com

        Copyright(C) 2016-2019 Bengbu Jixin Communication Machinery Co., Ltd

                                                        Record No:皖ICP備11019128號-1




        国产区精品系列在线观看-国产在线精品亚洲观看不卡欧美,亚洲制服丝袜欧美卡通,国产素人制服丝袜在线,国产最新区,中文欧美亚洲欧日韩,天堂亚洲小说区春色